Vibration Characteristics of Rock Under Harmonic Impact

Guodong JI, Haige WANG, Zhijian HU, Siqi LI, Tie YAN, Bing LI

Abstract


Modal analysis of rock is done in this study, and the results of numerical analysis are presented. Meanwhile, the amplitude-frequency characteristic curve of rock in steady state response is investigated based on the principle of vibration. In addition, indoor experiments are carried out to further analyze the vibration characteristics of rock under harmonic impact. Three main control parameters are considered, including drilling way, excitation frequency and impacting amplitude.
Our investigations confirm that the rock has different resonant frequencies and vibration modes in different orders for free vibration system, and there is only one resonant frequency for a rock with one degree of freedom. Based on theoretical analysis and indoor experiments, it can be concluded that the vibration amplitude under resonant frequency of rock is significantly higher than that under non-resonant frequency and in conventional drilling. Also, the vibration response of rock is in the harmonic form by the harmonic impact, and increases with the increase of the impacting amplitude.
The vibration characteristics of rock by harmonic impact are validated by numerical analysis and experimental results. Harmonic vibration impact drilling can greatly enhance the vibration amplitude of rock, and further improve the rate of penetration.


Keywords


Harmonic impact; Modal analysis; Amplitude-frequency characteristic; Resonant frequency; Indoor experiment

Full Text:

PDF

References


Wang, L., Guo, Z. Q., et al. (2005). Application of percussive-rotary drilling technology in oil wells. Drilling & Production Technology, 28(1), 8-10.

Jiang, H. W., Liu, Y. S., & Zhai, Y. H., et al. (2006). Research on rock-crushing mechanics model in rotary and percussive drilling. Petroleum Drilling Techniques, 31(1), 10-16.

Chang, D. Y., & Li, G. S., et al. (2011). The stress field of bottom hole in deep and ultra-deep wells. Acta Petrolei Sinica, 32(4), 697-703.

Shen, Z. H., Huang, H. C., & Gao, D. L. (2009). Analysis on new development and development trend of worldwide drilling technology. Journal of China University of Petroleum, 33(4), 64-70.

Batako, A. D., Babitsky, V. I., & Halliwell, N. A. (2004). Modelling of vibro-impact penetration of self-exciting percussive-rotary drill bit. Journal of Sound and Vibration, 271, 209-225.

Ostasevicius, V., & Gaidys, R., et al. (2010). An approach based on tool mode control for surface roughness reduction in high-frequency vibration cutting. Journal of Sound and Vibration, 329, 4866-4879.

Aguiar, R. R., & Weber, H. I. (2007). Development of a vibroimpact device for the resonance hammer drilling. Proceedings of the XII International Symposium on Dynamic Problems of Mechanics. Brazil.

Wiercigroch, M., Krivtsov, A. K., & Wojewoda, J. (2008). Vibrational energy transfer via modulated impacts for percussive drilling. Journal of Theoretical and Applied Mechanics, 46(3), 715-726.

Ajibose, O. K., Wiercigroch, M., & Pavlovskaia, E., et al. (2012). Drifting impact oscillator with a new model of the progression phase. Journal of Applied Mechanic, 79.

Pavlovskaia, E., Hendry, D. C., & Wiercigroch, M. (2013). Modelling of high frequency vibro-impact drilling. International Journal of Mechanical Sciences, 91, 110-119.

Pavlovskaia, E., & Wiercigroch, M. (2003). Modelling of vibro-impact system driven by beat frequency. International Journal of Mechanical Sciences, 45, 623-641.

Li, W., Yan, T., & Li, S. Q., et al. (2013). Rock response mechanism and rock breaking test analysis for impact of high frequency vibration drilling tool. Petroleum Drilling Techniques, 41(6), 25-28.

Li, W., Yan, T., & Bi, X. L. (2012). Apparatus and method for resonance drilling under high frequency pulse jet. C.N. Patent 201110394711. 8.

Zhang, Z. M., Zhou, X. D., & Jiang, D. J. (2009). Structural dynamics. China Electric Power Press.

Li, S. Q., Yan, T., & Li, W., et al. (2015). Modeling of vibration response of rock by harmonic impact. Journal of Natural Gas Science and Engineering, 23, 90-96.




DOI: http://dx.doi.org/10.3968/10124

Refbacks

  • There are currently no refbacks.


Copyright (c) 2018 Siqi LI

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Share us to:   

Reminder

  • How to do online submission to another Journal?
  • If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:

1. Register yourself in Journal B as an Author

  • Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.

2. Submission

  • Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.

We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
[email protected]; [email protected]; [email protected]

 Articles published in Advances in Petroleum Exploration and Development are licensed under Creative Commons Attribution 4.0 (CC-BY). 

ADVANCES IN PETROLEUM EXPLORATION AND DEVELOPMENT Editorial Office

Address:1055 Rue Lucien-L'Allier, Unit #772, Montreal, QC H3G 3C4, Canada.

Telephone: 1-514-558 6138
Website: Http://www.cscanada.net
Http://www.cscanada.org
E-mail:[email protected];  [email protected]

Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures