Study on the Affection of Drilling Tools’ Abrasion to the Regular Pattern of Tensile Strength

Zijie LI

Abstract


Drilling tool is a necessary tool in oil drilling engineering, its performance directly affects the penetration rate of drilling engineering, to a well, reasonable selection of drilling tools will be conductive to high-quality, efficient and fast drilling construction. Reasonable optimization of drilling tools, based on the field testing of drilling tools in use, and according to the results of field testing, correctly guide the selection of drilling tools. According to the different drilling conditions, the drilling tools should be reasonably allocated to match the drilling performance with the drilling conditions. Analyze the problems and causes of drilling tools found in testing, and determine the rational solutions and preventive measures. The abrasion and thinning of drilling tools often occurs in the drilling process of oil and gas, which affects the bearing capacity of drilling tools. Tensile load is one of the main load-bearing modes of drilling tools and an important evaluation index of drilling tool safety. By simplifying the drilling tool model, confirm the tensile strength of the wearing drilling tool and the stress state at different well depths, and reach the relationship between the wearing degree of drilling tool and the safe well depth.


Keywords


Testing of drilling tools; Oil drilling; Safety of drilling tools; Abrasion and thinning; Tensile strength

Full Text:

PDF

References


Dahnel, A. N., Ascroft, H., & Barnes, S. (2016). The effect of varying cutting speeds on tool wear during conventional and ultrasonic assisted drilling (UAD) of carbon fibre composite (CFC) and titanium alloy stacks. Procedia CIRP., 46, 420-423.

Ramirez, C., Poulachon, G., Rossi, F., & M’Saoubi, R. (2014). Tool wear monitoring and hole surface quality during CFRP drilling. Procedia CIRP, 13.

Samuel Raj, D., & Karunamoorthy, L. (2019, Jan.). Performance of cryogenically treated WC drill using tool wear measurements on the cutting edge and hole surface topography when drilling CFRP[J]. International Journal of Refractory Metals and Hard Materials, 78 .

Samuel Raj, D., & Karunamoorthy, L. (2018, April). A new and comprehensive characterisation of tool wear in CFRP drilling using micro-geometry and topography studies on the cutting edge. Journal of Manufacturing Processes, 32.

Arul, S., Samuel Raj, D., Vijayaraghavan, L., Malhotra, S. K., & Krishnamurthy, R. (2006). Modeling and optimization of process parameters for defect toleranced drilling of GFRP composites. Materials and Manufacturing Processes, (4).

Samuel Raj, D., & Karunamoorthy, L. (2016). Study of the Effect of Tool Wear on Hole Quality in Drilling CFRP to Select a Suitable Drill for Multi-Criteria Hole Quality. Materials and Manufacturing Processes, (5).




DOI: http://dx.doi.org/10.3968/10997

Refbacks

  • There are currently no refbacks.


Copyright (c) 2019 Zijie LI

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Share us to:   

Reminder

  • How to do online submission to another Journal?
  • If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:

1. Register yourself in Journal B as an Author

  • Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.

2. Submission

  • Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.

We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
[email protected]; [email protected]; [email protected]

 Articles published in Advances in Petroleum Exploration and Development are licensed under Creative Commons Attribution 4.0 (CC-BY). 

ADVANCES IN PETROLEUM EXPLORATION AND DEVELOPMENT Editorial Office

Address:1055 Rue Lucien-L'Allier, Unit #772, Montreal, QC H3G 3C4, Canada.

Telephone: 1-514-558 6138
Website: Http://www.cscanada.net
Http://www.cscanada.org
E-mail:[email protected];  [email protected]

Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures