Comparative Study of Using Oil-Based Mud Versus Water-Based Mud in HPHT Fields

Mahmood Amani, Mohammed Al-Jubouri, Arash Shadravan

Abstract


Growing demand for oil and gas is driving the exploration and production industry to look for new resources in un-explored areas, and in deeper formations. According to the Bureau of Ocean Energy Management, Regulation and Enforcement, former Minerals Management Service (MMS), over 50% of proven oil and gas reserves in the United States lie below 14,000 ft. subsea. In the Gulf of Mexico some wells were drilled at 27,000 ft below seabed with reservoir temperatures above 400 °F and reservoir pressures of 24,500 psi. As we drill into deeper formations we will experience higher pressures and temperatures.

Drilling into deeper formation requires drilling fluids that withstand higher temperatures and pressures. The combined pressure-temperature effect on drilling fluid’s rheology is complex. This provides a wide range of difficult challenges and mechanical issues. This can have negative impact on rheological properties when exposed to high pressure high temperature (HPHT) condition and contaminated with other minerals, which are common in deep drilling. High Pressure and High Temperature (HPHT) wells have bottom hole temperatures of 300 °F (150 °C) and bottom hole pressures of 10,000 psi (69 MPa) or higher.

Water-Based mud (WBM) and Oil-Based mud (OBM) are the most common drilling fluids currently used and both have several characteristics that qualify them for HPHT purposes. This paper compares the different characteristics of WBM and OBM to help decide the most suitable mud type for HPHT drilling by considering mud properties through several laboratory tests to generate some engineering guidelines. The tests were formulated at temperatures from 100 °F up to 600 °F and pressures from 5,000 psi to 25,000 psi. The comparison will mainly consider the rheological properties of the two mud types of mud and will also take into account the environmental feasibility of using them.

 Key words: Oil-based mud; Water-based mud; HPHT fields


Keywords


Oil-based mud; Water-based mud; HPHT fields

Full Text:

PDF

References


[1] Adamson, K., Birch, G., Gao, E., Hand, S., Macdonald, C., Mack, D., & Quadri, A. (1998). High-Pressure, High-Temperature Well Construction. Retrieved from https://www.slb.com/~/media/Files/resources/oilfield_review/ors98/sum98/pgs_36_49.pdf

[2] Alderman, N.J., Gavignet, A., Guillot, D., & Maitland, G.C. (1988). High-Temperature, High-Pressure Rheology of Water-Based Muds. Society of Petroleum Engineers. SPE Annual Technical Conference and Exhibition, 2-5 October 1988, Houston, Texas.

[3] Amani, M. (2012). The Rheological Properties of Oil-Based Mud Under High Pressure and High Temperature Conditions. Advances in Petroleum Exploration and Development, 3(2), 21-30.

[4] Amani, M., & Al-Jubouri, M. (2012). An Experimental Investigation of the Effects of Ultra High Pressures and Temperatures on the Rheological Properties of Water-Based Drilling Fluids. Society of Petroleum Engineers. DOI: 10.2118/157219-MS

[5] Amani, M., & Al-Jubouri, M. (2012). The Effect of High Pressures and High Temperatures on the Properties of Water Based Drilling Fluids. Energy Science and Technology, 4(1), 27-33.

[6] Bourgoyne Jr, A., Millheim, K., Chenevert, M., & Young Jr, F. S. (1986). Applied Drilling Engineering (SPE Textbook Series, Vol. 2). Society of Petroleum Engineers.

[7] Lee, J., Shadravan, A., & Young, S. (2012). Rheological Properties of Invert Emulsion Drilling Fluid Under Extreme HPHT Conditions. Society of Petroleum Engineers. DOI: 10.2118/151413-MS

[8] Shadravan, A., & Amani, M. (2012). HPHT 101-What Petroleum Engineers and Geoscientists Should Know about High Pressure High Temperature Wells Environment. Energy Science and Technology, 4(2), 36-60.

[9] Shadravan, Nabaei, M., & Amani, M. (2009). Dealing with the Challenges of UBD Implementation in Southern Iranian Oilfields. Society of Petroleum Engineers. DOI: 10.2118/125281-MS

[10] Shahri, M., & Zabihi, S. (2012). A New Model for Determining the Radius of Mud Loss During Drilling Operation in a Radial Fractured Network. Society of Petroleum Engineers. DOI: 10.2118/163028-MS

[11] Thaemlitz, C.J., Patel, A.D., Coffin, G., & Conn, L. (1999). New Environmentally Safe High-Temperature Water-Based Drilling-Fluid System. SPE Drilling & Completion, 14(3), 185-189.




DOI: http://dx.doi.org/10.3968/j.aped.1925543820120402.987

Refbacks

  • There are currently no refbacks.


Copyright (c)



Share us to:   

Reminder

  • How to do online submission to another Journal?
  • If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:

1. Register yourself in Journal B as an Author

  • Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.

2. Submission

  • Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.

We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
[email protected]; [email protected]; [email protected]

 Articles published in Advances in Petroleum Exploration and Development are licensed under Creative Commons Attribution 4.0 (CC-BY). 

ADVANCES IN PETROLEUM EXPLORATION AND DEVELOPMENT Editorial Office

Address:1055 Rue Lucien-L'Allier, Unit #772, Montreal, QC H3G 3C4, Canada.

Telephone: 1-514-558 6138
Website: Http://www.cscanada.net
Http://www.cscanada.org
E-mail:[email protected];  [email protected]

Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures