Simulation of Casing Stress in Thermal Recovery Production Wells

KANG Bo

Abstract


Thermal well technologies, such as Cyclic Steam Stimulation (CSS) and Steam Assisted Gravity Drainage (SAGD), have been widely used in the production of heavy oil reservoir. Casing failure generally exists in heavy oil thermal recovery production and becomes more and more serious. The three-dimension finite element model was developed by using ANSYS software, which applied in thermal structure coupling condition for casing, cementing hoop and rock. The influence of the parameters change on casing stress in thermal-structure coupling condition was studied. The results show that the equivalent stress can be significantly reduced by the application of high-quality insulated casing tube, borehole curvature should be as small as possible to minimum casing failure in heavy oil thermal recovery wells, casing tubes with low elastic modulus should be chosen.
Key words: Casing damage; Thermal recovery production; Finite element model; Elastic modulus; Cementing

Keywords


Casing damage; Thermal recovery production; Finite element model; Elastic modulus; Cementing

Full Text:

PDF

References


[1] Wang, Z. H., & Gao, D. L. (2003). The casing damage mechanisms and its control in thermal recovery wells. Petroleum Drilling Technology, 31(5), 46-48.

[2] Zhang, Y., Kuang, Y. C., Wu, K. S., et al. (2008). Research on casing failure mechanism of thermal production well based on finite element method. Drilling & Production Technology, 32(4), 102-104.

[3] Li, J. B., Shu, X. X., & Zheng, M. S. (2006). Bending resistant behavior of local defected oil well pipes. Journal of Safety Science and Technology, 2(5), 3-8.

[4] Zhang, H. P. (2009). Prevention and treatment recommendations of H2S at the scene of heavy oil thermal recovery in Liaohe Oilfield. Journal of Safety Science and Technology, 5(2), 178-180.

[5] Yu, L., & Bao, M. (2005). New technology for easing damage prevention and cure of thermal production wells in Liaohe Oilfield. Petroleum Exploration and Development, 32(1), 116-118.

[6] Li, J., Lin, C. Y., & Yang, S. C., et al. (2009). Analysis on mechanism of casing damage and strength design for heavy oil wells. Oil Field Equipment, 38(1), 9-13.

[7] Chen, Y., Lian, Z. H., & Chen, R. M. (2009). Analysis for casing safety evaluation based on residual stress in thermal well. Oil Field Equipment, 38(4), 16-19.

[8] Yang, X. J., Yang, L., Jia, S. P., et al. (2005). The finite element analysis of the casing failure mechanisms of thermal recovery wells in sand production. Oil Field Equipment, 34(2), 19-23.




DOI: http://dx.doi.org/10.3968/j.aped.1925543820140701.1855

Refbacks

  • There are currently no refbacks.


Copyright (c)



Share us to:   

Reminder

  • How to do online submission to another Journal?
  • If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:

1. Register yourself in Journal B as an Author

  • Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.

2. Submission

  • Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.

We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
[email protected]; [email protected]; [email protected]

 Articles published in Advances in Petroleum Exploration and Development are licensed under Creative Commons Attribution 4.0 (CC-BY). 

ADVANCES IN PETROLEUM EXPLORATION AND DEVELOPMENT Editorial Office

Address:1055 Rue Lucien-L'Allier, Unit #772, Montreal, QC H3G 3C4, Canada.

Telephone: 1-514-558 6138
Website: Http://www.cscanada.net
Http://www.cscanada.org
E-mail:[email protected];  [email protected]

Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures